Oak Faced Stair Cladding Risers

Write a review

SKU (JC005)

OVERVIEW

White Oak Faced MDF Riser Board for use with Basics and Solid oak Stair Tread. Supplied unfinished to match our White Oak Stair Parts - Select 1000mm or 1500mm Widths 

Read More


PRICE (including VAT)

£15.00


Availability

ITEM IN-STOCK Delivery Within 14 Days

Shipping

£35.00 (To Ship Entire Order)

Summary

Oak Stair Cladding Riser Boards 

10mm Oak Faced MDF Riser Board for use with Solid Oak Treads 

We use Oak faced MDF as an alternative to solid oak on the riser boards as we found 10mm thick solid oak had a tendency to bow and twist. MDF is a a very stable product and will not move before or after installation. The MDF is faced with Real Oak to Match our range of solid oak stair cladding 

The Solid Oak Stair Cladding Range is manufactured to order and is usually delivered between 7-10 working days 

This system fits over your existing treads & risers to convert it to a solid oak look.

Reconditioning your stairs may sound challenging, but with the new Contract range of readymade 20mm Solid Oak stair treads and faced risers it couldn’t be easier, just cut to size and stick over your existing treads.

Our range has everything you need to clad most configurations of staircases including straight flights, winder flights and quarter landings. The product has been designed to be as simple as possible with minimal preparatory work required. Simply remove your existing stair covering, sand any major unevenness, cut your treads to size and glue them in place with a polymer adhesive.

Treads are grooved on the back edge to accept Tread Extension T&G boards that fit together to cover winder steps and mid landing areas 

Solid Oak Cladding Stair Riser

10mm Oak Faced MDF 230mm (deep) 1000mm (wide) or 1500mm Wide 

Solid Oak Stair Cladding Fitting Guide

Before you start your stair cladding installation please read the instructions fully and contact us if you have any queries.

  1. Before you start, ensure that your existing steps and riser boards are clean, dry and free from uneven defects. We suggest you thoroughly sand the steps to ensure you get a good sound base for your new Stair Treads and Risers
  2. Measure the existing bullnose protrusion from the face of the existing riser board to the furthest point of the bullnose on the existing step. You can then cut packing strips from timber that will push the bottom of the Stair Riser board out and in line with the end of your bullnose. We suggest that these packing strips are screwed into place for stability.
  3. Starting at the Top of the staircase, measure and cut three Stair Risers to size and glue them onto the packing strips using polymer adhesive
  4. Measure the depth and width and cut a Stair Tread to size. Apply a 10mm bead of Flexible Polymer Adhesive to the top of your existing step
  5. Press the Stair Tread onto the Adhesive firmly ensuring the Stair Riser fits securely into the groove on the bottom of the Stair Tread
  6. Continue down the stairs fitting 3 riser boards first and then the treads.
  7. If you reach a mid-landing, then use the same method above but use Solid Oak Extension Boards to cover the landing area. These are supplied with a tongue and groove on the long edges that slot into the back edge of the tread.
  8. If you have large Kite Winder Steps, then you may need to use the 1500mm wide Stair Treads and Risers with Stair Extension Boards. You can usually use 1000mm Treads and Risers with Extension Boards for triangular shaped winders no wider than 1000mm
  9. Fix the stair treads and any joining riser boards first then cut the extension boards to size, apply a good amount of polymer adhesive and push the boards together until the area is covered. Do not put adhesive between the T&G joints.
  10. Work your way down the stairs to the bottom floor or use the Stair Klad Bottom Bullnose Step for cladding bullnose steps. This is supplied with a light oiled finish
  11. You will need to apply a coat of oil on your Stair after installation to ensure an even colour and protect the timber. Remember you will need to maintain your Stair Cladding after installation by oiling regularly to keep the timber looking fresh and protected

Once fitted the treads and risers will need to be finished with a good quality hardwood oil or varnish.

You can download the Cheshire Mouldings StairKlad Instructions manual from here

Specification

Oak Riser Board 

  • 10mm Oak Faced MDF 
  • 230mm Deep 
  • 1000mm or 1500mm Wide

You can download the Cheshire Mouldings StairKlad Instructions manual from here

StairKlad-Fitting-Instructions.pdf

(Right Click, Save Target As)

REVIEWS

There are no reviews for this product at the moment


Please log in to leave a review

We'll beat any like-for-like quote on
all stair parts.

Our online interactive stair planner allows you to browse, select and plan
your ideal staircase in 3 simple steps. Why not try it today?